Proxy Community
How to set up a simple proxy with auth Linux command? or What's the easiest way to create a simple pr - Printable Version

+- Proxy Community (https://proxycommunity.com/forum)
+-- Forum: Tutorials and Setup Guides (https://proxycommunity.com/forum/forum-tutorials-and-setup-guides)
+--- Forum: Router and Network-Wide Proxies (https://proxycommunity.com/forum/forum-router-and-network-wide-proxies)
+--- Thread: How to set up a simple proxy with auth Linux command? or What's the easiest way to create a simple pr (/thread-how-to-set-up-a-simple-proxy-with-auth-linux-command-or-what-s-the-easiest-way-to-create-a-simple-pr)

Pages: 1 2


How to set up a simple proxy with auth Linux command? or What's the easiest way to create a simple pr - SecureSeeker77 - 19-07-2024

"What's the easiest way to create a simple proxy with auth linux command?"

Hey folks,

I'm tired of overcomplicated setups. Just need a *simple proxy with auth linux command* that works without 10 layers of config.

Something like `tinyproxy` or `squid` but without the headache? Ideally, a one-liner or a few quick steps.

Bonus if it’s secure-ish (basic auth is fine).

Anyone got a quick solution? Or am I doomed to read man pages all night?

Thanks!

(PS: If it’s a "just use nginx" reply, pls explain like I’m 5.)


“” - ProxyVoyager99 - 13-10-2024

If you want a dead simple proxy with auth linux command, try `socat`. It's not fancy, but it gets the job done.

Here's a one-liner:
```
socat TCP-LISTEN:8080,fork,reuseaddr PROXY:yourproxy.com:target.com:80,proxyport=3128,proxyauth=user:pass
```

Not the most secure, but for quick & dirty, it works.


“” - MaskedPathX - 11-01-2025

Dude, just use `corkscrew` over SSH. It's like the lazy dev's dream for a simple proxy with auth.

```
ssh -D 8080 -o "ProxyCommand=corkscrew proxy.com 3128 %h %p" user@target
```

Boom. Auth handled by SSH, and you get a SOCKS proxy. No config hell.


“” - hyperNomadX - 24-01-2025

Honestly, `tinyproxy` isn’t that bad if you just want a simple proxy with auth linux command.

Edit `/etc/tinyproxy.conf`:
```
Port 8888
BasicAuth username password
```

Then `sudo systemctl restart tinyproxy`. Done.

Yeah, it’s not a one-liner, but it’s like 2 steps.


“” - webSurferX - 28-01-2025

For a no-frills simple proxy with auth, `redsocks` is underrated.

Config is minimal:
```
base {
log_debug = on;
proxy = "yourproxy:port";
username = "user";
password = "pass";
}
```

Start it with `redsocks -c /path/to/config`. Not glamorous, but it works.


“” - secureFly77 - 01-02-2025

Why not just `nc` (netcat) with auth? It’s janky but fits the "simple proxy with auth linux command" ask.

```
mkfifo pipe
nc -l -p 8080 < pipe | nc target.com 80 > pipe
```

Add auth with `htpasswd` if you’re feeling fancy. Not for production, but for testing? Sure.


“” - darkXchangeX - 23-02-2025

If you’re okay with Python, this one-liner might save you:

```
python3 -m http.server 8080 --proxy-auth user:pass
```

Wait, no—that’s not right. Actually, `pproxy` is better:

```
pproxy -l http://:8080 -a user:pass
```

Now *that’s* a simple proxy with auth linux command.


“” - SecureSeeker77 - 28-02-2025

OP here. Yo, thanks for all the replies! Tried `socat` and `tinyproxy`—both worked, but `pproxy` was the winner for me.

Quick q: Anyone know how to make `pproxy` auto-start on boot? Tried systemd but it’s being fussy.

Also, shoutout to the `corkscrew` suggestion—didn’t know that existed!